 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Features * * * * * * * * * * * * * * * 18.1SPECint95, Estimates 12.3 SPECfp95 at 400 MHz (PC755) 15.7SPECint95, 9SPECfp95 at 350 MHz (PC745) 733 MIPS at 400 MHz (PC755) at 641 MIPS at 350 MHz (PC745) Selectable Bus Clock (12 CPU Bus Dividers up to 10x) PD Typical 6.4W at 400 MHz, Full Operating Conditions Nap, Doze and Sleep Modes for Power Savings Superscalar (3 Instructions per Clock Cycle) Two Instruction + Branch 4 Beta Byte Virtual Memory, 4-GByte of Physical Memory 64-bit Data and 32-bit Address Bus Interface 32-KB Instruction and Data Cache Six Independent Execution Units Write-back and Write-through Operations fINT max = 400 MHz (TBC) fBUS max = 100 MHz Voltage I/O 2.5V/3.3V; Voltage Int 2.0V PowerPC 755/745 RISC Microprocessor PC755/745 Preliminary -site Description The PC755 and PC745 PowerPC (R) microprocessors are high-performance, lowpower, 32-bit implementations of the PowerPC Reduced Instruction Set Computer (RISC) architecture, especially enhanced for embedded applications. The PC755 and PC745 microprocessors differ only in that the PC755 features an enhanced, dedicated L2 cache interface with on-chip L2 tags. The PC755 is a drop-in replacement for the award winning PowerPC 750TM microprocessor and is footprint and user software code compatible with the MPC7400 microprocessor with AltiVecTM technology. The PC745 is a drop-in replacement for the PowerPC 740TM microprocessor and is also footprint and user software code compatible with the PowerPC 603eTM microprocessor. PC755/745 microprocessors provide on-chip debug support and are fully JTAG-compliant. The PC745 microprocessor is pin compatible with the TSPC603e family. ZF suffix PBGA255 Flip-Chip Plastic Ball Grid Array ZF suffix PBGA360 Flip-Chip Plastic Ball Grid Array G suffix CBGA360 Ceramic Ball Grid Array GS suffix CI-CGA360 Ceramic Ball Grid Array with Solder Column Interposer (SCI) GH suffix HITCE 360 Ceramic Ball Grid Array Rev. 2138D-HIREL-06/03 1 * * * Screening General Description Figure 1. PC755 Block Diagram This product is manufactured in full compliance with: 2 HiTCE Instruction Unit Fetcher BTIC 64-Entry SRs (Shadow) IBAT Array Tags 32-Kbyte I Cache ITLB BHT CTR LR Full military temperature range (Tj = -55C,+125C) industrial temperature range (Tj = -40C,+110C) CBGA + CI-CGA + FC-PBGA up screenings based upon Atmel standards PC755/745 Branch Processing Unit Instruction MMU 128-Bit (4 Instructions) Instruction Queue (6-Word) Dispatch Unit 64-Bit (2 Instructions) GPR File Rename Buffers (6) Rename Buffers (6) 32-Bit Load/Store Unit 64-Bit System Register Unit Reservation Station (2-Entry) FPR File Reservation Station Additional Features Time Base Counter/Decrementer Clock Multiplier JTAG/COP Interface Thermal/Power Management Performance Monitor 2 Instructions Reservation Station Reservation Station Reservation Station Integer Unit 1 Integer Unit 2 + (EA Calculation) 64-Bit Floating-Point Unit +xO CR Store Queue 32-Bit + +xO FPSCR FPSCR 32-Bit PA EA 60x Bus Interface Unit Data MMU 64-Bit Instruction Fetch Queue L1 Castout Queue DBAT Array Tags Data Load Queue 32-Kbyte D Cache SRs (Original) DTLB 32-Bit Address Bus 32-/64-Bit Data Bus 17-Bit L2 Address Bus 64-Bit L2 Data Bus Completion Unit Reorder Buffer (6-Entry) L2 Bus Interface Unit L2 Castout Queue L2 Controller L2CR L2 Tags Not in the PC745 Simplified Block Diagram The PC755 is targeted for low power systems and supports power management fea- tures such as doze, nap, sleep, and dynamic power management. The PC755 consists of a processor core and an internal L2 Tag combined with a dedicated L2 cache interface and a 60x bus. 2138D-HIREL-06/03 PC755/745 General Parameters The following list provides a summary of the general parameters of the PC755: Technology Die size Transistor count Logic design PC745 PC755 0.22 m CMOS, six-layer metal 6.61 mm x 7.73 mm (51 mm2) 6.75 million Fully-static Packages Surface mount 255 Plastic Ball Grid Array (PBGA) Surface mount 360 Plastic Ball Grid Array (PBGA) Surface mount 360 Ceramic Ball Grid Array (CI-CGA, CBGA, HiTCE) 2V 100 mV DC (nominal; some parts support core voltages down to 1.8V; see Table 5 for recommended operating conditions) 2.5V 100 mV DC or 3.3V 165 mV DC (input thresholds are configuration pin selectable) Core power supply I/O power supply Features This section summarizes features of the PC755's implementation of the PowerPC architecture. Major features of the PC755 are as follows: * Branch Processing Unit - - - - - * Four instructions fetched per clock One branch processed per cycle (plus resolving 2 speculations) Up to 1 speculative stream in execution, 1 additional speculative stream in fetch 512-entry branch history table (BHT) for dynamic prediction 64-entry, 4-way set associative Branch Target Instruction Cache (BTIC) for eliminating branch delay slots Full hardware detection of dependencies (resolved in the execution units) Dispatch two instructions to six independent units (system, branch, load/store, fixed-point unit 1, fixed-point unit 2, floating-point) Serialization control (predispatch, postdispatch, execution serialization) Register file access Forwarding control Partial instruction decode 6 entry completion buffer Instruction tracking and peak completion of two instructions per cycle Completion of instructions in program order while supporting out-of-order instruction execution, completion serialization and all instruction flow changes Fixed Point Unit 1 (FXU1)-multiply, divide, shift, rotate, arithmetic, logical Fixed Point Unit 2 (FXU2)-shift, rotate, arithmetic, logical Dispatch Unit - - - * Decode - - - * Completion - - - * Fixed Point Units (FXUs) that share 32 GPRs for Integer Operands - - 3 2138D-HIREL-06/03 - - - * - - - - - * - - * - - - - - - - - - - - - - - - - - - - - - * - - - - - Single-cycle arithmetic, shifts, rotates, logical Multiply and divide support (multi-cycle) Early out multiply Support for IEEE-754 standard single and double precision floating point arithmetic Hardware support for divide Hardware support for denormalized numbers Single-entry reservation station Supports non-IEEE mode for time-critical operations Executes CR logical instructions and miscellaneous system instructions Special register transfer instructions One cycle load or store cache access (byte, half-word, word, double-word) Effective address generation Hits under misses (one outstanding miss) Single-cycle unaligned access within double word boundary Alignment, zero padding, sign extend for integer register file Floating point internal format conversion (alignment, normalization) Sequencing for load/store multiples and string operations Store gathering Cache and TLB instructions Big and Little-endian byte addressing supported Misaligned Little-endian supported Level 1 Cache structure 32K, 32 bytes line, 8-way set associative instruction cache (iL1) 32K, 32 bytes line, 8-way set associative data cache (dL1) Cache locking for both instruction and data caches, selectable by group of ways Single-cycle cache access Pseudo least-recently used (PLRU) replacement Copy-back or Write Through data cache (on a page per page basis) Supports all PowerPC memory coherency modes Non-Blocking instruction and data cache (one outstanding miss under hits) No snooping of instruction cache Internal L2 cache controller and tags; external data SRAMs 256K, 512K, and 1-Mbyte 2-way set associative L2 cache support Copyback or write-through data cache (on a page basis, or for all L2) Instruction-only mode and data-only mode. 64 bytes (256K/512K) or 128 bytes (1M) sectored line size Floating-point Unit and a 32-entry FPR File System Unit Load/Store Unit Level 2 (L2) Cache Interface (not implemented on PC745) 4 PC755/745 2138D-HIREL-06/03 PC755/745 - Supports flow through (register-buffer) synchronous burst SRAMs, pipelined (register-register) synchronous burst SRAMs (3-1-1-1 or strobeless 4-1-1-1) and pipelined (register-register) late-write synchronous burst SRAMs L2 configurable to direct mapped SRAM interface or split cache/direct mapped or private memory Core-to-L2 frequency divisors of 1, 1.5, 2, 2.5, and 3 supported 64-bit data bus Selectable interface voltages of 2.5V and 3.3V Parity checking on both L2 address and data 128 entry, 2-way set associative instruction TLB 128 entry, 2-way set associative data TLB Hardware reload for TLBs Hardware or optional software tablewalk support 8 instruction BATs and 8 data BATs 8 SPRGs, for assistance with software tablewalks Virtual memory support for up to 4 hexabytes (252) of virtual memory Real memory support for up to 4 gigabytes (232) of physical memory Compatible with 60X processor interface 32-bit address bus 64-bit data bus, 32-bit mode selectable Bus-to-core frequency multipliers of 2x, 3x, 3.5x, 4x, 4.5x, 5x, 5.5x, 6x, 6.5x, 7x, 7.5x, 8x, 10x supported Selectable interface voltages of 2.5V and 3.3V. Parity checking on both address and data busses Low-power design with thermal requirements very similar to PC740/750. Selectable interface voltage of 1.8V/2.0V can reduce power in output buffers (compared to 3.3V) Three static power saving modes: doze, nap, and sleep Dynamic power management LSSD scan design IEEE 1149.1 JTAG interface One-ship thermal sensor and control logic Thermal Management Interrupt for software regulation of junction temperature - - - - - * - - - - - - - - * - - - - - - * - - - - * - - * - - Memory Management Unit Bus Interface Power Management Testability Integrated Thermal Management Assist Unit 5 2138D-HIREL-06/03 Pin Assignments Figure 2 (in part A) shows the pinout of the PC745, 255PBGA package as viewed from the top surface. Part B shows the side profile of the PBGA package to indicate the direction of the top surface view. Figure 2. Pinout of the PC745, 255 PBGA Package as Viewed from the Top Surface Part A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A B C D E F G H J K L M N P R T Not to Scale Part B Substrate Assembly Encapsulant View Die 6 PC755/745 2138D-HIREL-06/03 PC755/745 Figure 3 (in part A) shows the pinout of the PC755, 360 PBGA packages as viewed from the top surface. Part B shows the side profile of the PBGA package to indicate the direction of the top surface view. Figure 3. Pinout of the PC755, 360 PBGA, CBGA and CI-CGA Packages as Viewed from the Top Surface Part A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 A B C D E F G H J K L M N P R T U V W Not to Scale Part B Substrate Assembly Encapsulant View Die 7 2138D-HIREL-06/03 Pinout Listings Table 1 provides the pinout listing for the PC745, 255 PBGA package. Table 1. Pinout Listing for the PC745, 255 PBGA Package I/F Voltages Supported(1) Signal Name A[0-31] Pin Number C16, E4, D13, F2, D14, G1, D15, E2, D16, D4, E13, G2, E15, H1, E16, H2, F13, J1, F14, J2, F15, H3, F16, F4, G13, K1, G15, K2, H16, M1, J15, P1 L2 K4 C1, B4, B3, B2 J4 A10 L1 B6 (3)(4)(5) Active High I/O I/O 1.8V/2.0V - 3.3V - AACK ABB AP[0-3] ARTRY AVDD BG BR BVSEL CI CKSTP_IN CKSTP_OUT CLK_OUT DBB DBG DBDIS DBWO DH[0-31] Low Low High Low - Low Low High Low Low Low - Low Low Low Low High Input I/O I/O I/O - Input Output Input Output Input Output Output I/O Input Input Input I/O - - - - 2V - - GND - - - - - - - - - - - - - 2V - - 3.3V - - - - - - - - - B1 E1 D8 A6 D7 J14 N1 H15 G4 P14, T16, R15, T15, R13, R12, P11, N11, R11, T12, T11, R10, P9, N9, T10, R9, T9, P8, N8, R8, T8, N7, R7, T7, P6, N6, R6, T6, R5, N5, T5, T4 K13, K15, K16, L16, L15, L13, L14, M16, M15, M13, N16, N15, N13, N14, P16, P15, R16, R14, T14, N10, P13, N12, T13, P3, N3, N4, R3, T1, T2, P4, T3, R4 M2, L3, N2, L4, R1, P2, M4, R2 G16 F1 C5, C12, E3, E6, E8, E9, E11, E14, F5, F7, F10, F12, G6, G8, G9, G11, H5, H7, H10, H12, J5, J7, J10, J12, K6, K8, K9, K11, L5, L7, L10, L12, M3, M6, M8, M9, M11, M14, P5, P12 A7 B15 D11 D12 B10 DL[0-31] High I/O - - DP[0-7] DRTRY GBL GND High Low Low I/O Input I/O - - - - - - HRESET INT L1_TSTCLK(2) L2_TSTCLK(2) LSSD_MODE (2) Low Low High High Low Input Input Input Input Input - - - - - - - - - -- 8 PC755/745 2138D-HIREL-06/03 PC755/745 Table 1. Pinout Listing for the PC745, 255 PBGA Package (Continued) I/F Voltages Supported(1) Signal Name MCP NC (NoConnect) OVDD PLL_CFG[0-3] QACK QREQ RSRV SMI SRESET SYSCLK TA TBEN TBST TCK TDI (5) Pin Number C13 B7, B8, C3, C6, C8, D5, D6, H4, J16, A4, A5, A2, A3, B5 C7, E5, E7, E10, E12, G3, G5, G12, G14, K3, K5, K12, K14, M5, M7, M10, M12, P7, P10 A8, B9, A9, D9 D3 J3 D1 A16 B14 C9 H14 C2 A14 C11 A11 A12 H13 C4 B11 C10 J13 A13, D10, B12 B13, A15, B16, C14, C15 D2 F6, F8, F9, F11, G7, G10, H6, H8, H9, H11, J6, J8, J9, J11, K7, K10, L6, L8, L9, L11 F3 Active Low - - High Low Low Low Low Low - Low High Low High High High Low Low High Low Low High High Low - High I/O Input - - Input Input Output Output Input Input Input Input Input I/O Input Input Output Input Input Input Input I/O Output I/O Output - Output 1.8V/2.0V - - 1.8V/2.0V - - - - - - - - - - - - - - - - - - - - - 2V - 3.3V - - 3.3V - - - - - - - - - - - - - - - - - - - - - 2V - TDO TEA TLBISYNC TMS (5) (5) TRST TS TSIZ[0-2] TT[0-4] WT VDD 2 VOLTDET(6) Notes: 1. OVDD supplies power to the processor bus, JTAG, and all control signals and VDD supplies power to the processor core and the PLL (after filtering to become AVDD). These columns serve as a reference for the nominal voltage supported on a given signal as selected by the BVSEL pin configuration of Table 4 and the voltage supplied. For actual recommended value of VIN or supply voltages see Table 3. 2. These are test signals for factory use only and must be pulled up to OVDD for normal machine operation. 3. To allow for future I/O voltage changes, provide the option to connect BVSEL independently to either OVDD (selects 3.3V) or to OGND (selects 1.8V/2.0V). 4. Uses one of 15 existing no-connects in PC745's 255-BGA package. 5. Internal pull up on die. 6. Internally tied to GND in the PC745 255-BGA package to indicate to the power supply that a low-voltage processor is present. This signal is not a power supply input. 9 2138D-HIREL-06/03 Table 2 provides the pinout listing for the PC755, 360 PBGA, CBGA and CI-CGA + HiTCE Table 2. Pinout Listing for the PC755, 360 PBGA, CBGA and CI-CGA Packages + HiTCE(8) I/F Voltages Supported(1) Signal Name A[0-31] Pin Number A13, D2, H11, C1, B13, F2, C13, E5, D13, G7, F12, G3, G6, H2, E2, L3, G5, L4, G4, J4, H7, E1, G2, F3, J7, M3, H3, J2, J6, K3, K2, L2 N3 L7 C4, C5, C6, C7 L6 A8 H1 E7 W1 C2 B8 D7 E3 K5 G1 K1 D1 W12, W11, V11, T9, W10, U9, U10, M11, M9, P8, W7, P9, W9, R10, W6, V7, V6, U8, V9, T7, U7, R7, U6, W5, U5, W4, P7, V5, V4, W3, U4, R5 M6, P3, N4, N5, R3, M7, T2, N6, U2, N7, P11, V13, U12, P12, T13, W13, U13, V10, W8, T11, U11, V12, V8, T1, P1, V1, U1, N1, R2, V3, U3, W2 L1, P2, M2, V2, M1, N2, T3, R1 H6 B1 D10, D14, D16, D4, D6, E12, E8, F4, F6, F10, F14, F16, G9, G11, H5, H8, H10, H12, H15, J9, J11, K4, K6, K8, K10, K12, K14, K16, L9, L11, M5, M8, M10, M12, M15, N9, N11, P4, P6, P10, P14, P16, R8, R12, T4, T6, T10, T14, T16 B6 C11 (2) Active High I/O I/O 1.8V/2.0V - 3.3V - AACK ABB AP[0-3] ARTRY AVDD BG BR BVSEL(3)(5)(6) CI CKSTP_IN CKSTP_OUT CLK_OUT DBB DBDIS DBG DBWO DH[0-31] Low Low High Low Low Low High Low Low Low - Low Low Low Low High Input I/O I/O I/O Input Output Input Output Input Output Output I/O Input Input Input I/O - - - - 2V - - GND - - - - - - - - - - - - - 2V - - 3.3V - - - - - - - - - DL[0-31] High I/O - - DP[0-7] DRTRY GBL GND High Low Low - I/O Input I/O - - - - GND - - - GND HRESET INT L1_TSTCLK Low Low High High Input Input Input Output - - - - - - - - F8 L17, L18, L19, M19, K18, K17, K15, J19, J18, J17, J16, H18, H17, J14, J13, H19, G18 L2ADDR[0-16] 10 PC755/745 2138D-HIREL-06/03 PC755/745 Table 2. Pinout Listing for the PC755, 360 PBGA, CBGA and CI-CGA Packages + HiTCE(8) (Continued) I/F Voltages Supported(1) Signal Name L2AVDD L2CE L2CLKOUTA L2CLKOUTB L2DATA[0-63] Pin Number L13 P17 N15 L16 U14, R13, W14, W15, V15, U15, W16, V16, W17, V17, U17, W18, V18, U18, V19, U19, T18, T17, R19, R18, R17, R15, P19, P18, P13, N14, N13, N19, N17, M17, M13, M18, H13, G19, G16, G15, G14, G13, F19, F18, F13, E19, E18, E17, E15, D19, D18, D17, C18, C17, B19, B18, B17, A18, A17, A16, B16, C16, A14, A15, C15, B14, C14, E13 V14, U16, T19, N18, H14, F17, C19, B15 D15, E14, E16, H16, J15, L15, M16, P15, R14, R16, T15, F15 L14 M14 F7 A19 N16 G17 F9 B11 B3, B4, B5, W19, K9, K11 , K19 4 4 Active - Low - - High I/O - Output Output Output I/O 1.8V/2.0V 2V - - - - 3.3V 2V - - - - L2DP[0-7] L2OVDD L2SYNC_IN L2SYNC_OUT L2_TSTCLK(2) L2VSEL L2WE L2ZZ LSSD_MODE(2) MCP NC (No-Connect) OVDD PLL_CFG[0-3] QACK QREQ RSRV SMI SRESET SYSCLK TA TBEN TBST TCK TDI (6) (1)(3)(5)(6) High - - - High High Low High Low Low - - High Low Low Low Low Low - Low High Low High High High I/O - Input Output Input Input Output Output Input Input - - Input Input Output Output Input Input Input Input Input I/O Input Input Output - 1.8V/2V - - - GND - - - - - 1.8V/2V - - - - - - - - - - - - - - 3.3V - - - 3.3V - - - - - 3.3V - - - - - - - - - - - - - D5, D8, D12, E4, E6, E9, E11, F5, H4, J5, L5, M4, P5, R4, R6, R9, R11, T5, T8, T12 A4, A5, A6, A7 B2 J3 D3 A12 E10 H9 F1 A2 A11 B10 B7 D9 TDO 11 2138D-HIREL-06/03 Table 2. Pinout Listing for the PC755, 360 PBGA, CBGA and CI-CGA Packages + HiTCE(8) (Continued) I/F Voltages Supported(1) Signal Name TEA TLBISYNC TMS (6) Pin Number J1 A3 C8 A10 K7 A9, B9, C9 C10, D11, B12, C12, F11 C3 G8, G10, G12, J8, J10, J12, L8, L10, L12, N8, N10, N12 Active Low Low High Low Low High High Low - High I/O Input Input Input Input I/O Output I/O Output - Output 1.8V/2.0V - - - - - - - - 2V - 3.3V - - - - - - - - 2V - TRST(6) TS TSIZ[0-2] TT[0-4] WT VDD VOLTDET Notes: (7) K13 1. OVDD supplies power to the processor bus, JTAG, and all control signals except the L2 cache controls (L2CE, L2WE, and L2ZZ); L2OVDD supplies power to the L2 cache interface (L2ADDR[0-16], L2DATA[0-63], L2DP[0-7] and L2SYNC-OUT) and the L2 control signals; and VDD supplies power to the processor core and the PLL and DLL (after filtering to become AVDD and L2AVDD respectively). These columns serve as a reference for the nominal voltage supported on a given signal as selected by the BVSEL/L2VSEL pin configurations of Table 4 and the voltage supplied. For actual recommended value of VIN or supply voltages see Table 5. 2. These are test signals for factory use only and must be pulled up to OVDD for normal machine operation. 3. To allow for future I/O voltage changes, provide the option to connect BVSEL and L2VSEL independently to either OVDD (selects 3.3V) or to OGND (selects 1.8V/2.0V). 4. These pins are reserved for potential future use as additional L2 address pins. 5. Uses one of 9 existing no-connects in PC750's 360-BGA package. 6. Internal pull up on die. 7. Internally tied to L2OVDD in the PC755 360-BGA package to indicate the power present at the L2 cache interface. This signal is not a power supply input. 8. This is different from the PC745 255-BGA package. 12 PC755/745 2138D-HIREL-06/03 PC755/745 Signal Description Figure 4. PC755 Microprocessor Signal Groups L2VDD L2AVDD BR ADDRESS ARBITRATION BG ABB TS A[0-31] ADDRESS BUS AP[0-3] Not supported in the PC745B 1 1 1 17 64 8 1 1 2 1 1 L2ADDR [16-0] L2DATA [0-63] L2DP [0-7] L2CE L2WE L2CLK-OUT [A-B] L2SYNC_OUT L2SYNC_IN L2ZZ INT SMI MCP SRESET HRESET CKSTP_IN CKSTP_OUT RSRV TBEN TLBISYNC QREQ QACK SYSCLK, PLL_CFG [0-3] CLK_OUT L2 VSEL L2 CACHE ADDRESS/ DATA ADDRESS START 1 32 4 L2 CACHE CLOCK/CONTROL TT[0-4] TBST TS1Z[0-2] GBL TRANSFER ATTRIBUTE WT CI 5 1 3 1 1 1 PC755B 1 1 1 1 1 1 1 1 1 1 INTERRUPTS RESET AACK ADDRESS TERMINATION ARTRY DBG DATA ARBITRATION DATA TRANSFER DBWO DBB D[0-63] D[P0-7] DBDIS 1 1 1 1 1 64 8 1 1 1 1 4 1 PROCESSOR STATUS CONTROL CLOCK CONTROL 5 3 JTAG:COP Factory Test TEST INTERFACE DATA TERMINATION TA DRTRY TEA 1 1 1 1 VOLTDET VDD AVDD OVDD GND 13 2138D-HIREL-06/03 Detailed Specification Scope Applicable Documents This drawing describes the specific requirements for the microprocessor PC755, in compliance with Atmel Grenoble standard screening. 1) MIL-STD-883: Test methods and procedures for electronics. 2) MIL-PRF-38535 appendix A: General specifications for microcircuits. Requirements General Design and Construction Terminal Connections Depending on the package, the terminal connections is shown in Table 1, Table 2 and Figure 4. The microcircuits are in accordance with the applicable documents and as specified herein. Absolute Maximum Rating Table 3. Absolute Maximum Ratings(1) Characteristic Core supply voltage(4) PLL supply voltage (4) (4) Symbol VDD AVDD L2AVDD OVDD L2OVDD Processor bus L2 Bus (2)(5) (2)(5) Maximum Value -0.3 to 2.5 -0.3 to 2.5 -0.3 to 2.5 -0.3 to 3.6 -0.3 to 3.6 -0.3 to OVDD + 0.3V -0.3 to L2OVDD + 0.3V -0.3 to 3.6 -65 to 150 220 Unit V V V V V V V V C C L2 DLL supply voltage Processor bus supply voltage(3) L2 bus supply voltage(3) Input voltage Vin Vin Vin Tstg Trwk JTAG Signals Storage temperature range Rework Temperature Notes: 1. Functional and tested operating conditions are given in Table 5. Absolute maximum ratings are stress ratings only, and functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause permanent damage to the device. 2. Caution: VIN must not exceed OVDD or L2OVDD by more than 0.3V at any time including during power-on reset. 3. Caution: L2OVDD/OVDD must not exceed VDD/AVDD/L2AVDD by more than 1.6V during normal operation. During power-on reset and power-down sequences, L2OVDD/OVDD may exceed VDD/AVDD/L2AVDD by up to 3.3V for up to 20 ms, or by 2.5V for up to 40 ms. Excursions beyond 3.3V or 40 ms are not supported. 4. Caution: VDD/AVDD/L2AVDD must not exceed L2OVDD/OVDD by more than 0.4V during normal operation. During power-on reset and power-down sequences, VDD/AVDD/L2AVDD may exceed L2OVDD/OVDD by up to 1.0V for up to 20 ms, or by 0.7V for up to 40 ms. Excursions beyond 1.0V or 40 ms are not supported. 5. This is a DC specifications only. VIN may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 5. 14 PC755/745 2138D-HIREL-06/03 PC755/745 Figure 5 shows the allowable undershoot and overshoot voltage on the PC755 and PC745. Figure 5. Overshoot/Undershoot Voltage (L2) OVDD +20% (L2) OVDD +5% (L2) OVDD VIH VIL Gnd Gnd - 0.3V Gnd - 1.0V Not to exceed 10% of tSYSCLK The PC755 provides several I/O voltages to support both compatibility with existing systems and migration to future systems. The PC755 core voltage must always be provided at nominal 2.0V (see Table 5 for actual recommended core voltage). Voltage to the L2 I/Os and Processor Interface I/Os are provided through separate sets of supply pins and may be provided at the voltages shown in Table 4. The input voltage threshold for each bus is selected by sampling the state of the voltage select pins BVSEL and L2VSEL during operation. These signals must remain stable during part operation and cannot change. The output voltage will swing from GND to the maximum voltage applied to the OVDD or L2OVDD power pins. Table 4 describes the input threshold voltage setting. Table 4. Input Threshold Voltage Setting Part Revision E BVSEL Signal 0 1 Notes: Processor Bus Interface Voltage Not Available 2.5V/3.3V L2VSEL Signal 0 1 L2 Bus Interface Voltage Not Available 2.5V/3.3V 1. Caution: The input threshold selection must agree with the OVDD/L2OVDD voltages supplied. 2. The input threshold settings above are different for all revisions prior to Rev. 2.8 (Rev. E). For more information, contact your local Atmel sales office. 15 2138D-HIREL-06/03 Table 5. Recommended Operating Conditions(1) Recommended Value 300 MHz, 350 MHz Characteristic Core supply voltage (3) 400 MHz Min 1.90 1.90 1.90 2.375 3.135 2.375 3.135 GND GND GND -55 -40 Max 2.10 2.10 2.10 2.625 3.465 2.625 3.465 OVDD L2OVDD OVDD 125 110 Unit Symbol VDD AVDD L2AVDD (2)(4)(5) Min 1.80 1.80 1.80 2.375 3.135 Max 2.10 2.10 2.10 2.625 3.465 2.625 3.465 OVDD L2OVDD OVDD 125 110 V V V V V V V V V V C C PLL supply voltage(3) L2 DLL supply voltage(3) Processor bus supply voltage BVSEL = 1 OVDD L2 bus supply voltage(2)(4)(5) L2VSEL = 1 L2OVDD 2.375 3.135 Input voltage Processor bus L2 Bus JTAG Signals Vin Vin Vin Tj Tj GND GND GND -55 -40 Die-junction temperature Military temperature range Industrial temperature Notes: 1. These are the recommended and tested operating conditions. Proper device operation outside of these conditions is not guaranteed. 2. Revisions prior to Rev. 2.8 (Rev. E) offered different I/O voltage support. 3. 2.0V nominal. 4. 2.5V nominal. 5. 3.3V nominal. Thermal Characteristics Package Characteristics Table 6 provides the package thermal characteristics for the PC755. Table 6. Package Thermal Characteristics Value Characteristic Junction-to-ambient thermal resistance, natural convection(1)(2) Junction-to-ambient thermal resistance, natural convection, four-layer (2s2p) board(1)(3) Junction-to-ambient thermal resistance, 200 ft./min. airflow, single-layer (1s) board(1)(3) Junction-to-ambient thermal resistance, 200 ft./min. airflow, four-layer (2s2p) board(1)(3) Junction-to-board thermal resistance(4) Junction-to-case thermal resistance Notes: (5) Symbol RJA RJMA RJMA RJMA RJB RJC PC755 CBGA 24 17 18 14 8 < 0.1 PC755 PBGA 31 25 25 21 17 < 0.1 PC745 PBGA 34 26 27 22 17 < 0.1 Unit C/W C/W C/W C/W C/W C/W 1. Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. 2. Per SEMI G38-87 and JEDEC JESD51-2 with the single layer board horizontal. 3. Per JEDEC JESD51-6 with the board horizontal. 16 PC755/745 2138D-HIREL-06/03 PC755/745 4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1) with the calculated case temperature. The actual value of REyJC for the part is less than 0.1C/W. Note: Refer to Section "Thermal Management Information" page 19 for more details about thermal management. Package Thermal Characteristics for HiTCE Table 7 provides the package thermal characteristics for the PC755, HiTCE. Table 7. Package Thermal Characteristics for HiTCE Package Value Characteristic Junction-to-bottom of balls (1) Symbol RJ RJMA RJB PC755 HiTCE 6.8 20.7 11.0 Unit C/W C/W C/W Junction-to-ambient thermal resistance, natural convection, four-layer (2s2p) board(1)(2) Junction to board thermal resistance Notes: 1. Simulation, no convection air flow. 2. Per JEDEC JESD51-6 with the board horizontal. Table 8. Package Thermal Characteristics for CI-CGA Value Characteristic Junction to board thermal resistance Symbol RJB PC755 CI-CGA 8.42 Unit C/W The board designer can choose between several types of heat sinks to place on the PC755. There are several commercially-available heat sinks for the PC755 provided by the following vendors: For the exposed-die packaging technology, shown in Table 5, the intrinsic conduction thermal resistance paths are as follows: * * The die junction-to-case (or top-of-die for exposed silicon) thermal resistance The die junction-to-ball thermal resistance Figure 6 depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit board. Heat generated on the active side of the chip is conducted through the silicon, then through the heat sink attach material (or thermal interface material), and finally to the heat sink where it is removed by forced-air convection. Since the silicon thermal resistance is quite small, for a first-order analysis, the temperature drop in the silicon may be neglected. Thus, the heat sink attach material and the heat sink conduction/convective thermal resistances are the dominant terms. 17 2138D-HIREL-06/03 Figure 6. C4 Package with Head Sink Mounted to a Printed-circuit Board External Resistance Radiation Convection Heat Sink Thermal Interface Material Internal Resistance Die/Package Die Junction Package/Leads Printed Circuit Board External Resistance Radiation Convection Note the internal versus external package resistance. Thermal Management Assistance The PC755 incorporates a thermal management assist unit (TAU) composed of a thermal sensor, digital-to-analog converter, comparator, control logic, and dedicated special-purpose registers (SPRs). Specifications for the thermal sensor portion of the TAU are found in Table 9. More information on the use of this feature is given in the Motorola PC755 RISC Microprocessor User's manual. Table 9. Thermal Sensor Specifications at Recommended Operating Conditions (see Table 5) Characteristic Temperature range (1) (2)(3) Min 0 20 4 -12 Max 127 - - +12 Unit C s Comparator settling time Resolution (3) C C Accuracy(3) Notes: 1. The temperature is the junction temperature of the die. The thermal assist unit's raw output does not indicate an absolute temperature, but must be interpreted by software to derive the absolute junction temperature. For information about the use and calibration of the TAU, see Motorola Application Note AN1800/D, "Programming the Thermal Assist Unit in the PC750 Microprocessor". 2. The comparator settling time value must be converted into the number of CPU clocks that need to be written into the THRM3 SPR. 3. Guaranteed by design and characterization. 18 PC755/745 2138D-HIREL-06/03 PC755/745 Thermal Management Information This section provides thermal management information for the ceramic ball grid array (BGA) package for air-cooled applications. Proper thermal control design is primarily dependent upon the system-level design-the heat sink, airflow and thermal interface material. To reduce the die-junction temperature, heat sinks may be attached to the package by several methods-adhesive, spring clip to holes in the printed-circuit board or package, and mounting clip and screw assembly; see Figure 7. This spring force should not exceed 5.5 pounds of force. Figure 7. Package Exploded Cross-Sectional View with Several Heat Sink Options Heat Sink Heat Sink Clip Adhesive or Thermal Interface Material BGA Package Printed Circuit Board Option Ultimately, the final selection of an appropriate heat sink depends on many factors, such as thermal performance at a given air velocity, spatial volume, mass, attachment method, assembly, and cost. 19 2138D-HIREL-06/03 Adhesives and Thermal Interface Materials Figure 8. Thermal Performance of Select Thermal Interface Material 2 Silicone Sheet (0.006 inch) Bare Joint Floroether Oil Sheet (0.007 inch) Graphite/Oil Sheet (0.005 inch) Synthetic Grease Specific Thermal Resistance (Kin2/W) 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 Contact Pressure (psi) A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the thermal contact resistance. For those applications where the heat sink is attached by spring clip mechanism, Figure 8 shows the thermal performance of three thin-sheet thermal-interface materials (silicone, graphite/oil, floroether oil), a bare joint, and a joint with thermal grease as a function of contact pressure. As shown, the performance of these thermal interface materials improves with increasing contact pressure. The use of thermal grease significantly reduces the interface thermal resistance. That is, the bare joint results in a thermal resistance approximately 7 times greater than the thermal grease joint. Heat sinks are attached to the package by means of a spring clip to holes in the printedcircuit board (see Figure 7). This spring force should not exceed 5.5 pounds of force. Therefore, the synthetic grease offers the best thermal performance, considering the low interface pressure. The board designer can choose between several types of thermal interface. Heat sink adhesive materials should be selected based upon high conductivity, yet adequate mechanical strength to meet equipment shock/vibration requirements. Heat Sink Selection Example For preliminary heat sink sizing, the die-junction temperature can be expressed as follows: Tj = Ta + Tr + (jc + int + sa) * Pd Where: Tj is the die-junction temperature Ta is the inlet cabinet ambient temperature Tr is the air temperature rise within the computer cabinet 20 PC755/745 2138D-HIREL-06/03 PC755/745 jc is the junction-to-case thermal resistance int is the adhesive or interface material thermal resistance sa is the heat sink base-to-ambient thermal resistance Pd is the power dissipated by the device During operation the die-junction temperatures (Tj) should be maintained less than the value specified in Table 5. The temperature of the air cooling the component greatly depends upon the ambient inlet air temperature and the air temperature rise within the electronic cabinet. An electronic cabinet inlet-air temperature (Ta) may range from 30 to 40C. The air temperature rise within a cabinet (Tr) may be in the range of 5 to 10C. The thermal resistance of the thermal interface material (int) is typically about 1C/W. Assuming a Ta of 30C, a Tr of 5oC, a CBGA package jc = 0.03, and a power consumption (Pd) of 5.0 watts, the following expression for Tj is obtained: Die-junction temperature: Tj = 30C + 5C + (0.03C/W + 1.0C/W + sa) * 5.0 W For a Thermalloy heat sink #2328B, the heat sink-to-ambient thermal resistance (sa) versus airflow velocity is shown in Figure 9. Figure 9. Thermalloy #2328B Heat Sink-to-Ambient Thermal Resistance Versus Airflow Velocity 8 Thermalloy #2328B Pinfin Heat Sink (25 x28 x 15 mm) 7 Heat Sink Thermal Resistance C/W) 6 5 4 3 2 1 0 0.5 1 1.5 2 2.5 3 3.5 Approach Air Velocity (m/s) Assuming an air velocity of 0.5 m/s, we have an effective Rsa of 7C/W, thus Tj = 30C+ 5C+ (0.03C/W +1.0C/W + 7C/W) * 5.0 W, resulting in a die-junction temperature of approximately 81C which is well within the maximum operating temperature of the component. Other heat sinks offered by Chip Coolers, IERC, Thermalloy, Wakefield Engineering, and Aavid Engineering offer different heat sink-to-ambient thermal resistances, and may or may not need air flow. 21 2138D-HIREL-06/03 Though the die junction-to-ambient and the heat sink-to-ambient thermal resistances are a common figure-of-merit used for comparing the thermal performance of various microelectronic packaging technologies, one should exercise caution when only using this metric in determining thermal management because no single parameter can adequately describe three-dimensional heat flow. The final die-junction operating temperature, is not only a function of the component-level thermal resistance, but the system-level design and its operating conditions. In addition to the component's power consumption, a number of factors affect the final operating die-junction temperature -- airflow, board population (local heat flux of adjacent components), heat sink efficiency, heat sink attach, heat sink placement, next-level interconnect technology, system air temperature rise, altitude, etc. Due to the complexity and the many variations of system-level boundary conditions for today's microelectronic equipment, the combined effects of the heat transfer mechanisms (radiation, convection and conduction) may vary widely. For these reasons, we recommend using conjugate heat transfer models for the board, as well as, system-level designs. To expedite system-level thermal analysis, several "compact" thermal-package models are available within FLOTHERM(R). These are available upon request. Power consideration Power management The PC755 provides four power modes, selectable by setting the appropriate control bits in the MSR and HIDO registers. The four power modes are as follows: * Full-power: This is the default power state of the PC755. The PC755 is fully powered and the internal functional units operate at the full processor clock speed. If the dynamic power management mode is enabled, functional units that are idle will automatically enter a low-power state without affecting performance, software execution, or external hardware. Doze: All the functional units of the PC755 are disabled except for the time base/decrementer registers and the bus snooping logic. When the processor is in doze mode, an external asynchronous interrupt, a system management interrupt, a decrementer exception, a hard or soft reset, or machine check brings the PC755 into the full-power state. The PC755 in doze mode maintains the PLL in a fully powered state and locked to the system external clock input (SYSCLK) so a transition to the full-power state takes only a few processor clock cycles. Nap: The nap mode further reduces power consumption by disabling bus snooping, leaving only the time base register and the PLL in a powered state. The PC755 returns to the full-power state upon receipt of an external asynchronous interrupt, a system management interrupt, a decrementer exception, a hard or soft reset, or a machine check input (MCP). A return to full-power state from a nap state takes only a few processor clock cycles. When the processor is in nap mode, if QACK is negated, the processor is put in doze mode to support snooping. Sleep: Sleep mode minimizes power consumption by disabling all internal functional units, after which external system logic may disable the PPL and SUSCLK. Returning the PC755 to the full-power state requires the enabling of the PPL and SYSCLK, followed by the assertion of an external asynchronous interrupt, a system management interrupt, a hard or soft reset, or a machine check input (MCP) signal after the time required to relock the PPL. * * * 22 PC755/745 2138D-HIREL-06/03 PC755/745 Power Dissipation Table 10. Power Consumption for PC755 Processor (CPU) Frequency 300 MHz Full-Power Mode Typical(1)(3)(4) Maximum (1)(2) 350 MHz 400 MHz Unit 3.1 4.5 3.6 5.3 5.4 8 W W Doze Mode Maximum(1)(2)(4) Nap Mode Maximum(1)(2)(4) Sleep Mode Maximum(1)(2)(4) 550 550 550 mW 1 1 1 W 1.8 2 2.3 W Sleep Mode-PLL and DLL Disabled Maximum(1)(2) Notes: 510 510 510 mW 1. These values apply for all valid processor bus and L2 bus ratios. The values do not include I/O supply power (OVDD and L2OVDD) or PLL/DLL supply power (AVDD and L2AVDD). OVDD and L2OVDD power is system dependent, but is typically < 10% of VDD power. Worst case power consumption for AVDD = 15 mW and L2AVDD = 15 mW. 2. Maximum power is measured at nominal VDD (see Table 5) while running an entirely cache-resident, contrived sequence of instructions which keep the execution units maximally busy. 3. Typical power is an average value measured at the nominal recommended VDD (see Table 5) and 65xC in a system while running a typical code sequence. 4. Not 100% tested. Characterized and periodically sampled. 23 2138D-HIREL-06/03 Electrical Characteristics Static Characteristics Table 11. DC Electrical Specifications at Recommended Operating Conditions (see Table 5) Characteristic Input high voltage (all inputs except SYSLCK)(2)(3) Nominal bus Voltage(1) 2.5 3.3 Input low voltage (all inputs except SYSLCK) (2) Symbol VIH VIH VIL VIL KVIH KVIH KVIL KVIL Iin ITSI Min 1.6 2 -0.3 -0.3 1.8 2.4 -0.3 -0.3 - - 1.7 2.4 - - - Max (L2)OVDD + 0.3 (L2)OVDD + 0.3 0.6 0.8 OVDD + 0.3 OVDD + 0.3 0.4 0.4 10 10 - - 0.45 0.4 5 Unit V V V V V V V V A A V V V V pF 2.5 3.3 SYSCLK input high voltage 2.5 3.3 SYSCLK input low voltage 2.5 3.3 Input leakage current, (2)(3) VIN = L2OVDD/OVDD Hi-Z (off-state) leakage current, (2)(3)(5) VIN = L2OVDD/OVDD Output high voltage, IOH = -6 mA 2.5 3.3 Output low voltage, IOL = 6 mA Capacitance, VIN = 0V, f = 1 MHz (3)(4) Notes: 1. 2. 3. 4. 5. 2.5 3.3 VOH VOH VOL VOL Cin Nominal voltages; See Table 5 for recommended operating conditions. For processor bus signals, the reference is OVDD while L2OVDD is the reference for the L2 bus signals. Excludes test signals (LSSD_MODE, L1_TSTCLK, L2_TSTCLK) and IEEE 1149.1 boundary scan (JTAG) signals. Capacitance is periodically sampled rather than 100% tested. The leakage is measured for nominal OVDD and VDD, or both OVDD and VDD must vary in the same direction (for example, both OVDD and VDD vary by either +5% or -5%). Dynamic Characteristics After fabrication, parts are sorted by maximum processor core frequency as shown in the "Clock AC Specifications" Section on page 25 and tested for conformance to the AC specifications for that frequency. These specifications are for 275, 300, 333 MHz processor core frequencies. The processor core frequency is determined by the bus (SYSCLK) frequency and the settings of the PLL_CFG[0-3] signals. Parts are sold by maximum processor core frequency. 24 PC755/745 2138D-HIREL-06/03 PC755/745 Clock AC Specifications Table 12 provides the clock AC timing specifications as defined in Table 3. Table 12. Clock AC Timing Specifications at Recommended Operating Conditions (See Table 5) Maximum Processor Core Frequency 300 MHz Characteristic Processor frequency(1) VCO frequency (1) (1) 350 MHz Min 200 400 25 10 - - 40 - - Max 350 700 100 40 2 1.4 60 150 100 400 MHz Min 200 400 25 10 - - 40 - - Max 400 800 100 40 2 1.4 60 150 100 Unit Symbol fcore fVCO fSYSCLK tSYSCLK tKR & tKF tKR & tKF (3) Min 200 400 25 10 - - 40 - - Max 300 600 100 40 2 1.4 60 150 100 MHz MHz MHz ns ns ns % ps s SYSCLK frequency SYSCLK cycle time SYSCLK rise and fall time(2) SYSCLK duty cycle measured at OVDD/2 SYSCLK jitter(3)(4) Internal PLL relock time(3)(5) Notes: tKHKL/tSYSCLK 1. Caution: The SYSCLK frequency and PLL_CFG[0-3] settings must be chosen such that the resulting SYSCLK (bus) frequency, CPU (core) frequency, and PLL (VCO) frequency do not exceed their respective maximum or minimum operating frequencies. Refer to the PLL_CFG[0-3] signal description in Table 18," for valid PLL_CFG[0-3] settings 2. Rise and fall times measurements are now specified in terms of slew rates, rather than time to account for selectable I/O bus interface levels. The minimum slew rate of 1v/ns is equivalent to a 2ns maximum rise/fall time measured at 0.4V and 2.4V or a rise/fall time of 1ns measured at 0.4V to 1.4V. 3. Timing is guaranteed by design and characterization. 4. This represents total input jitter - short term and long term combined and is guaranteed by design. 5. Relock timing is guaranteed by design and characterization. PLL-relock time is the maximum amount of time required for PLL lock after a stable VDD and SYSCLK are reached during the power-on reset sequence. This specification also applies when the PLL has been disabled and subsequently re-enabled during sleep mode. Also note that HRESET must be held asserted for a minimum of 255 bus clocks after the PLL-relock time during the power-on reset sequence. Figure 10 provides the SYSCLK input timing diagram. Figure 10. SYSCLK Input Timing Diagram SYSCLK VM tKHKL tSYSCLK VM = Midpoint Voltage (OVDD/2) VM VM KVIH KVIL tKR tKF 25 2138D-HIREL-06/03 Processor Bus AC Specifications Table 13 provides the processor bus AC timing specifications for the PC755 as defined in Figure 11 and Figure 13. Timing specifications for the L2 bus are provided in Section "L2 Clock AC Specifications page 28. Table 13. Processor Bus Mode Selection AC Timing Specifications(1) At VDD = AVDD = 2.0V 100 mV; -55 Tj +125C, OVDD = 3.3V 165 mV and OVDD = 1.8V 100 mV and OVDD = 2.0V 100 mV Symbols(2) Parameter Mode select input setup to HRESET(3)(4)(5)(6)(7) HRESET to mode select input hold(3)(4)(6)(7)(8) Notes: tMVRH tMXRH All Speed Grades Min 8 0 Max - - Unit tSYSCLk ns 1. All input specifications are measured from the midpoint of the signal in question to the midpoint of the rising edge of the input SYSCLK. All output specifications are measured from the midpoint of the rising edge of SYSCLK to the midpoint of the signal in question. All output timings assume a purely resistive 50 load (See Figure 11). Input and output timings are measured at the pin; time-of-flight delays must be added for trace lengths, vias, and connectors in the system. 2. THe symbology used for timing specifications herein follows the pattern of t(signal)(state)(reference)(state) for inputs and t(reference)(state)(signal)(state) for outputs. For example, tIVKH symbolizes the time input signals (I) reach the valid state (V) relative to the SYSCLK reference (K) going to the high (H) state or input setup time. And tKHOV symbolizes the time from SYSCLK(K) going highs) until outputs (O) are valid (V) or output valid time. Input hold time can be read as the time that the input signal (I) went invalid (X) with respect to the rising clock edge (KH) - note the position of the reference and its state for inputs - and output hold time can be read as the time from the rising edge (KH) until the output went invalid (OX). For additional explanation of AC timing specifications in Motorola PowerPC microprocessors, see the application note "Understanding AC Timing Specifications for PowerPC Microprocessors." 3. The setup and hold time is with respect to the rising edge of HRESET (see Figure 11). 4. This specification is for configuration mode select only. Also note that the HRESET must be held asserted for a minimum of 255 bus clocks after the PLL re-lock time during the power-on reset sequence. 5. tSYSCLK is the period of the external clock (SYSCLK) in nanoseconds (ns). The numbers given in the table must be multiplied by the period of SYSCLK to compute the actual time duration (in nanoseconds) of the parameter in question. 6. Mode select signals are BVSEL, L2VSEL, PLL_CFG[0-3] 7. Guaranteed by design and characterization. 8. Bus mode select pins must remain stable during operation. Changing the logic states of BVSEL or L2VSEL during operation will cause the bus mode voltage selection to change. Changing the logic states of the PLL_CFG pins during operation will cause the PLL division ratio selection to change. Both of these conditions are considered outside the specification and are not supported. Once HRESET is negated the states of the bus mode selection pins must remain stable. Figure 11 provides the mode select input timing diagram for the PC755. Figure 11. Mode Input Timing Diagram HRESET VM tMVRH tMXRH MODE SIGNALS VM = Midpoint Voltage (OVDD/2) 26 PC755/745 2138D-HIREL-06/03 PC755/745 Figure 12 provides the AC test load for the PC755. Figure 12. AC Test Load OUTPUT Z0 = 50 RL = 50 OVDD/2 Table 14. Processor Bus AC Timing Specifications(1) at Recommended Operating Conditions All Speed Grades Unit Parameter Setup Times: All Inputs Input Hold Times: TLBISYNC, MCP, SMI Input Hold Times: All Inputs, except TLBISYNC, MCP, SMI Valid Times: All Outputs Output Hold Times: All Outputs SYSCLK to Output Enable (2) Symbols tIVKH tIXKH tIXKH tKHOV tKHOX tKHOE tKHOZ tKHABPZ tKHARP (2)(3)(5) (2)(3)(4) Min 2.5 0.6 0.2 - 1 0.5 - - - - Max - - - 4.1 - - 6 1 1 2 ns ns ns ns ns ns ns tSYSCLK tSYSCLK tSYSCLK SYSCLK to Output High Impedance (all except ABB, ARTRY, DBB)(2) SYSCLK to ABB, DBB High Impedance After Precharge Maximum Delay to ARTRY Precharge (2)(3)(5) SYSCLK to ARTRY High Impedance After Precharge Notes: tKHARPZ 1. Revisions prior to Rev 2.8 (Rev E) were limited in performance and did not conform to this specification. Contact your local Motorola sales office for more information. 2. Guaranteed by design and characterization. 3. tSYSCLK is the period of the external clock (SYSCLK) in nanoseconds (ns). The numbers given in the table must be multiplied by the period of SYSCLK to compute the actual time duration (in ns) of the parameter in question. 4. Per the 60x bus protocol, TS, ABB and DBB are driven only by the currently active bus master. They are asserted low then precharged high before returning to high-Z as shown in Figure 6. The nominal precharge width for TS, ABB or DBB is 0.5 x tSYSCLK, i.e. less than the minimum tSYSCLK period, to ensure that another master asserting TS, ABB, or DBB on the following clock will not contend with the precharge. Output valid and output hold timing is tested for the signal asserted. Output valid time is tested for precharge.The high-Z behavior is guaranteed by design. 5. Per the 60x bus protocol, ARTRY can be driven by multiple bus masters through the clock period immediately following AACK. Bus contention is not an issue since any master asserting ARTRY will be driving it low. Any master asserting it low in the first clock following AACK will then go to high-Z for one clock before precharging it high during the second cycle after the assertion of AACK. The nominal precharge width for ARTRY is 1.0 tSYSCLK; i.e., it should be high-Z as shown in Figure 6 before the first opportunity for another master to assert ARTRY. Output valid and output hold timing is tested for the signal asserted. Output valid time is tested for precharge. The high-Z and precharge behavior is guaranteed by design. 27 2138D-HIREL-06/03 Figure 13 provides the input/output timing diagram for the PC755. Figure 13. Input/Output Timing Diagram SYSCLK VM tIVKH VM tIXKH VM ALL INPUTS tKHOE tKHOV ALL OUTPUTS (Except TS, ABB, ARTRY, DBB) tKHOX tKHOZ tKHABPZ tKHOZ tKHOX tKHOV TS,ABB,DBB tKHARPZ tKHOV tKHARP tKHOX tKHOV ARTRY VM = Midpoint Voltage (OVDD/2 or Vin/2) L2 Clock AC Specifications The L2CLK frequency is programmed by the L2 Configuration Register (L2CR[4:6]) core-to-L2 divisor ratio. See Table 15 for example core and L2 frequencies at various divisors. Table 15 provides the potential range of L2CLK output AC timing specifications as defined in Figure 14. The minimum L2CLK frequency of Table 15 is specified by the maximum delay of the internal DLL. The variable-tap DLL introduces up to a full clock period delay in the L2CLKOUTA, L2CLKOUTB, and L2SYNC_OUT signals so that the returning L2SYNC_IN signal is phase aligned with the next core clock (divided by the L2 divisor ratio). Do not choose a core-to-L2 divisor which results in an L2 frequency below this minimum, or the L2CLKOUT signals provided for SRAM clocking will not be phase aligned with the PC755 core clock at the SRAMs. The maximum L2CLK frequency shown in Table 15 is the core frequency divided by one. Very few L2 SRAM designs will be able to operate in this mode. Most designs will select a greater core-to-L2 divisor to provide a longer L2CLK period for read and write access to the L2 SRAMs. The maximum L2CLK frequency for any application of the PC755 will be a function of the AC timings of the PC755, the AC timings for the SRAM, bus loading, and printed circuit board trace length. 28 PC755/745 2138D-HIREL-06/03 PC755/745 Motorola is similarly limited by system constraints and cannot perform tests of the L2 interface on a socketed part on a functional tester at the maximum frequencies of Table 15. Therefore functional operation and AC timing information are tested at core-to-L2 divisors of 2 or greater. Functionality of core-to-L2 divisors of 1 or 1.5 is verified at less than maximum rated frequencies. L2 input and output signals are latched or enabled respectively by the internal L2CLK (which is SYSCLK multiplied up to the core frequency and divided down to the L2CLK frequency). In other words, the AC timings of Table 16 and Table 17 are entirely independent of L2SYNC_IN. In a closed loop system, where L2SYNC_IN is driven through the board trace by L2SYNC_OUT, L2SYNC_IN only controls the output phase of L2CLKOUTA and L2CLKOUTB which are used to latch or enable data at the SRAMs. However, since in a closed loop system L2SYNC_IN is held in phase alignment with the internal L2CLK, the signals of Table 16 and Table 17 are referenced to this signal rather than the not-externally-visible internal L2CLK. During manufacturing test, these times are actually measured relative to SYSCLK. The L2SYNC_OUT signal is intended to be routed halfway out to the SRAMs and then returned to the L2SYNC_IN input of the PC755 to synchronize L2CLKOUT at the SRAM with the processor's internal clock. L2CLKOUT at the SRAM can be offset forward or backward in time by shortening or lengthening the routing of L2SYNC_OUT to L2SYNC_IN. See Motorola Application Note AN179/D "PowerPCTM Backside L2 Timing Analysis for the PCB Design Engineer." The L2CLKOUTA and L2CLKOUTB signals should not have more than two loads. Table 15. L2CLK Output AC Timing Specification. At VDD = AVDD = 2.0V 100 mV; -55 Tj +125C, OVDD = 3.3V 165 mV and OVDD = 1.8V 100 mV and OVDD = 2.0V 100 mV All Speed Grades Parameter L2CLK frequency (1)(4) Symbols f L2CLK t L2CLK tCHCL/tL2CLK - - (6)(7) Min 80 2.5 45 640 0 - - Max 450 12.5 55 - 10 50 150 Unit MHz ns % L2CLK ns ps ps L2CLK cycle time L2CLK duty cycle(2)(7) Internal DLL-relock time(3)(7) DLL capture window (5)(7) L2CLKOUT output-to-output skew L2CLKOUT output jitter(6)(7) Notes: tL2CSKW - 1. L2CLK outputs are L2CLK_OUTA, L2CLK_OUTB, L2CLK_OUT and L2SYNC_OUT pins. The L2CLK frequency to core frequency settings must be chosen so that the resulting L2CLK frequency and core frequency do not exceed their respective maximum or minimum operating frequencies. The maximum L2LCK frequency will be system dependent. L2CLK_OUTA and L2CLK_OUTB must have equal loading. 2. The nominal duty cycle of the L2CLK is 50% measured at midpoint voltage. 3. The DLL re-lock time is specified in terms of L2CLKs. The number in the table must be multiplied by the period of L2CLK to compute the actual time duration in nanoseconds. Re-lock timing is guaranteed by design and characterization. 4. The L2CR[L2SL] bit should be set for L2CLK frequencies less than 110 MHz. This adds more delay to each tap of the DLL. 5. Allowable skew between L2SYNC_OUT and L2SYNC_IN. 6. This output jitter number represents the maximum delay of one tap forward or one tap back from the current DLL tap as the phase comparator seeks to minimize the phase difference between L2SYNC_IN and the internal L2CLK. This number must be comprehended in the L2 timing analysis. The input jitter on SYSCLK affects L2CLKOUT and the L2 address/data/control signals equally and therefore is already comprehended in the AC timing and does not have to be considered in the L2 timing analysis. 7. Guaranteed by design. 29 2138D-HIREL-06/03 The L2CLK_OUT timing diagram is shown in Figure 14. Figure 14. L2CLK_OUT Output Timing Diagram L2 Single-Ended Clock Mode tL2CLK tCHCL L2CLK_OUTA VM VM VM tL2CR tL2CF L2CLK_OUTB VM VM VM tL2CSKW VM L2SYNC_OUT VM VM VM VM L2 Differential Clock Mode L2CLK_OUTB L2CLK_OUTA tL2CLK tCHCL VM VM VM L2SYNC_OUT VM VM VM VM = Midpoint Voltage (L2OVdd/2) L2 Bus Input AC Specifications Table 16 provides the L2 bus interface AC timing specifications for the PC755 as defined in Figure 15 and Figure 16 for the loading conditions described in Figure 17. All Speed Grades Table 16. L2 Bus Interface AC Timing Specifications at Recommended Operating Conditions Parameter L2SYNC_IN rise and Fall Time Setup Times: Data and Parity (1) Symbol tL2CR & tL2CF tDVL2CH (2) Min - 1.2 0 - Max 1.0 3.1 3.2 3.3 3.7 Unit ns ns ns ns (2) Input Hold Times: Data and Parity tDXL2CH tL2CHOV Valid Times: (3)(4) All Outputs when L2CR[14-15] = 00 All Outputs when L2CR[14-15] = 01 All Outputs when L2CR[14-15] = 10 All Outputs when L2CR[14-15] = 11 Output Hold Times: (3) All Outputs when L2CR[14-15] = 00 All Outputs when L2CR[14-15] = 01 All Outputs when L2CR[14-15] = 10 All Outputs when L2CR[14-15] = 11 L2SYNC_IN to High Impedance:(3)(5) All Outputs when L2CR[14-15] = 00 All Outputs when L2CR[14-15] = 01 All Outputs when L2CR[14-15] = 10 All Outputs when L2CR[14-15] = 11 tL2CHOX 0.5 0.7 0.9 1.1 tL2CHOZ 2.4 2.6 2.8 3.0 - ns ns 30 PC755/745 2138D-HIREL-06/03 PC755/745 Notes: 1. Rise and fall times for the L2SYNC_IN input are measured from 20% to 80% of L2OVDD. 2. All input specifications are measured from the midpoint of the signal in question to the midpoint voltage of the rising edge of the input L2SYNC_IN (see Figure 8). Input timings are measured at the pins. 3. All output specifications are measured from the midpoint voltage of the rising edge of L2SYNC_IN to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50 load (See Figure 10). 4. The outputs are valid for both single-ended and differential L2CLK modes. For pipelined registered synchronous BurstRAMs, L2CR[14-15] = 01 or 10 is recommended. For pipelined late write synchronous BurstRAMs, L2CR[14-15] = 11 is recommended. 5. Guaranteed by design and characterization. 6. Revisions prior to Rev 2.8 (Rev E) were limited in performance.and did not conform to this specification. Contact your local Atmel sales office for more information. Figure 15 shows the L2 bus input timing diagrams for the PC755. Figure 15. L2 Bus Input Timing Diagrams tL2CR tL2CF L2SYNC_IN tDVL2CH VM tDXL2CH L2 DATA AND DATA PARITY INPUTS VM = Midpoint Voltage (L2OVDD/2) Figure 16 shows the L2 bus output timing diagrams for the PC755. Figure 16. L2 Bus Output Timing Diagrams L2SYNC_IN VM tL2CHOV VM tL2CHOX ALL OUTPUTS tL2CHOZ L2DATA BUS VM = Midpoint Voltage (L2OVDD/2) Figure 17 provides the AC test load for L2 interface of the PC755. Figure 17. AC Test Load for the L2 Interface OUTPUT Z0 = 50 RL = 50 L2OVdd/2 31 2138D-HIREL-06/03 IEEE 1149.1 AC Timing Specifications Timing Specifications Table 17 provides the IEEE 1149.1 (JTAG) AC timing specifications as defined in Figure 18, Figure 19, Figure 20, and Figure 21. Table 17. JTAG AC Timing Specifications (Independent of SYSCLK)(1) Parameter TCK Frequency of operation TCK Cycle time TCK Clock pulse width measured at 1.4V TCK Rise and fall times TRST Assert time(2) Input Setup Times: (3) Symbol fTCLK fTCLK tJHJL tJR & tJF tTRST Boundary-scan data TMS, TDI tDVJH tIVJH tDXJH tIXJH tJLDV tJLOV tJLDV tJLOV tJLDZ tJLOZ Min 0 62.5 31 0 25 4 0 15 12 25 12 3 3 Max 16 2 - Unit MHz ns ns ns ns ns Input Hold Times:(3) Boundary-scan data TMS, TDI Valid Times:(4) Boundary-scan data TDO Output Hold Times:(4) Boundary-scan data TDO TCK to output high impedance:(4)(5) Boundary-scan data TDO Notes: 19 9 4 4 - ns ns ns ns 1. All outputs are measured from the midpoint voltage of the falling/rising edge of TCLK to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50 load (See Figure 18). Time-of-flight delays must be added for trace lengths, vias, and connectors in the system. 2. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only. 3. Non-JTAG signal input timing with respect to TCK. 4. Non-JTAG signal output timing with respect to TCK. 5. Guaranteed by design and characterization. Figure 18 provides the AC test load for TDO and the boundary-scan outputs of the PC755. Figure 18. ALTERNATE AC Test Load for the JTAG Interface OUTPUT Z0 = 50 RL = 50 OVDD/2 32 PC755/745 2138D-HIREL-06/03 PC755/745 Figure 19 provides the JTAG clock input timing diagram. Figure 19. JTAG Clock Input Timing Diagram TCLK VM tJHJL tTCLK VM = Midpoint Voltage (OVDD/2) VM VM tJR tJF Figure 20 provides the TRST timing diagram. Figure 20. TRST Timing Diagram TRST VM tTRST VM = Midpoint Voltage (OVDD/2) VM Figure 21 provides the boundary-scan timing diagram. Figure 21. Boundary-Scan Timing Diagram TCK VM t DVJH BOUNDARY DATA INPUTS tJL DV tJLDH BOUNDARY DATA OUTPUTS OUTPUT DATA VALID INPUT DATA VALID VM t DXJH t JL DZ BOUNDARY DATA OUTPUTS OUTPUT DATA VALID VM = Midpoint Voltage (OVDD/2) 33 2138D-HIREL-06/03 Figure 22 provides the test access port timing diagram. Figure 22. Test Access Port Timing Diagram TCK VM t IVJH TDI, TMS tJLOV tJLOH TDO OUTPUT DATA VALID INPUT DATA VALID VM t IXJH tJLOZ TDO OUTPUT DATA VALID VM = Midpoint Voltage (OVDD/2) JTAG Configuration Signals Boundary scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the IEEE 1149.1 specification, but is provided on all processors that implement the PowerPC architecture. While it is possible to force the TAP controller to the reset state using only the TCK and TMS signals, more reliable power-on reset performance will be obtained if the TRST signal is asserted during power-on reset. Because the JTAG interface is also used for accessing the common on-chip processor (COP) function, simply tying TRST to HRESET is not practical. The COP function of these processors allows a remote computer system (typically, a PC with dedicated hardware and debugging software) to access and control the internal operations of the processor. The COP interface connects primarily through the JTAG port of the processor, with some additional status monitoring signals. The COP port requires the ability to independently assert HRESET or TRST in order to fully control the processor. If the target system has independent reset sources, such as voltage monitors, watchdog timers, power supply failures, or push-button switches, then the COP reset signals must bemerged into these signals with logic. The arrangement shown in Figure 23 allows the COP port to independently assert HRESET or TRST, while ensuring that the target can drive HRESET as well. If the JTAG interface and COP header will not be used, TRST should be tied to HRESET through a 0 isolation resistor so that it is asserted when the systemreset signal (HRESET) is asserted ensuring that the JTAG scan chain is initialized during power-on. While Motorola recommends that the COP header be designed into the system as shown in Figure 23, if this is not possible, the isolation resistor will allow future access to TRST in the casewhere a JTAG interfacemay need to be wired onto the system in debug situations. The COP header shown in Figure 23 adds many benefits -- breakpoints, watchpoints, register and memory examination/modification, and other standard debugger features are possible through this interface -- and can be as inexpensive as an unpopulated footprint for a header to be added when needed. The COP interface has a standard header for connection to the target system, based on the 0.025" square-post 0.100" centered header assembly (often called a Berg header). The connector typically has pin 14 removed as a connector key. 34 PC755/745 2138D-HIREL-06/03 PC755/745 Figure 23. JTAG Interface Connection SRESET From Target Board Sources (if any) HRESET QACK 13 11 HRESET SRESET 10 k 10 k 10 k 10 k 05 1 3 5 7 9 11 2 4 6 8 10 12 SRESET HRESET OVDD OVDD OVDD OVDD TRST 4 6 5 1 TRST OVDD OVDD CHKSTP_OUT 10 k OVDD 10 k OVDD VDD_SENSE 2 k CHKSTP_OUT 10 k 15 Key 14 2 KEY 13 No pin CHKSTP_IN COP Header 8 TMS 9 1 3 7 2 10 12 16 QACK TDO TDI TCK CHKSTP_IN TMS TDO TDI TCK QACK 15 16 COP Connector Physical Pin Out NC NC 2 k 3 10 k 4 OVDD Notes: 1. RUN/STOP, normally found on pin 5 of the COP header, is not implemented on the PC755. Connect pin 5 of the COP header to OVDD with a 10 k pull-up resistor. 2. Key location; pin 14 is not physically present on the COP header. 3. Component not populated. Populate only if debug tool does not drive QACK. 4. Populate only if debug tool uses an open-drain type output and does not actively deassert QACK. 5. If the JTAG interface is implemented, connect HRESET from the target source to TRST from the COP header though an AND gate to TRST of the part. If the JTAG interface is not implemented, connect HRESET fromthe target source to TRST of the part through a 0 isolation resistor. 35 2138D-HIREL-06/03 The COP header shown in Figure 24 adds many benefits--breakpoints, watchpoints, register and memory examination/modification and other standard debugger features are possible through this interface - and can be as inexpensive as an unpopulated footprint for a header to be added when needed. System design information The COP interface has a standard header for connection to the target system, based on the 0.025" square-post 0.100" centered header assembly (often called a "Berg" header). The connector typically has pin 14 removed as a connector key. Figure 24 shows the COP connector diagram. Figure 24. COP Connector Diagram CKSTP_OUT RUN/STOP HRESET SRESET TMS TDO TCK TDI TOP VIEW 15 13 KEY 11 9 10 7 8 5 6 3 4 1 2 16 No pin 12 Pins 10, 12 and 14 are no-connects. Pin 14 is not physically present CHKSTP_IN VDD_SENSE There is no standardized way to number the COP header shown in Figure 24; consequently, many different pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then left-to-right, while others use left-to-right then top-tobottom, while still others number the pins counter clockwise from pin one (as with an IC). Regardless of the numbering, the signal placement recommended in Figure 24 is common to all known emulators. The QACK signal shown in Table 17 is usually hooked up to the PCI bridge chip in a system and is an input to the PC755 informing it that it can go into the quiescent state. Under normal operation this occurs during a low power mode selection. In order for COP to work the PC755 must see this signal asserted (pulled down). While shown on the COP header, not all emulator products drive this signal. To preserve correct power down operation, QACK should be merged so that it also can be driven by the PCI bridge. 36 PC755/745 2138D-HIREL-06/03 Ground QACK TRST PC755/745 Preparation for Delivery Packaging Certificate of Compliance Microcircuits are prepared for delivery in accordance with MIL-PRF-38535. Atmel offers a certificate of compliances with each shipment of parts, affirming the products are in compliance either with MIL-PRF-883 and guarantying the parameters not tested at temperature extremes for the entire temperature range. MOS devices must be handled with certain precautions to avoid damage due to accumulation of static charge. Input protection devices have been designed in the chip to minimize the effect of static buildup. However, the following handling practices are recommended: 1. Devices should be handled on benches with conductive and grounded surfaces. 2. Ground test equipment, tools and operator. 3. Do not handle devices by the leads. 4. Store devices in conductive foam or carriers. 5. Avoid use of plastic, rubber, or silk in MOS areas. 6. Maintain relative humidity above 50 percent if practical. 7. For CI-CGA packages, use specific tray to take care of the highest height of the package compared with the normal CBGA. Handling Package Mechanical Data The following sections provide the package parameters and mechanical dimensions for the PC745, 255 PBGA package as well as the PC755, 360 CBGA and PBGA packages. While both the PC755 plastic and the ceramic packages are described here, both packages are not guaranteed to be available at the same time. All new designs should allow for either ceramic or plastic BGA packages for this device. For more information on designing a common footprint for both plastic and ceramic package types, please contact your local Motorola sales office. Parameters for the PC745 Package Parameters for the PC745 PBGA The package parameters are as provided in the following list. The package type is 21 x 21 mm, 255-lead plastic ball grid array (PBGA). Package outline Interconnects Pitch Minimum module height Maximum module height Ball diameter (typical) Mechanical Dimensions of the PC745 PBGA Package 21 x 21 mm 255 (16 x 16 ball array - 1) 1.27 mm (50 mil) 2.25 mm 2.80 mm 0.75 mm (29.5 mil) Figure 25 provides the mechanical dimensions and bottom surface nomenclature of the PC745, 255 PBGA package. 37 2138D-HIREL-06/03 Figure 25. Mechanical Dimensions and Bottom Surface Nomenclature of the PC745 PBGA 0.2 D A1 CORNER A C 0.15 C E NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. TOP SIDE A1 CORNER INDEX IS A METALIZED FEATURE WITH VARIOUS SHAPES. BOTTOM SIDE A1 CORNER IS DESIGNATED WITH A BALL MISSING FROM THE ARRAY. 4. CAPACITOR PADS MAY BE UNPOPULATED. 2X 0.2 B 1 2 3 4 5 6 7 8 9 10 111213141516 T R P N M L K J H G F E D C B A Table 1 Millimeters DIM M Min 2.25 0.50 1.00 0.60 Max 2.80 0.70 1.20 0.90 A A1 A2 A2 A1 A b D E e 21.00 BSC 21.00 BSC 1.27 BSC e 255X b 0.3 C A B 0.15 C Parameters for the PC755 PBGA Package Parameter for the PC755 PBGA The package parameters are as provided in the following list. The package type is 25 x 25 mm, 360-lead plastic ball grid array (PBGA). Package outline Interconnects Pitch Minimum module height Maximum module height Ball diameter 25 x 25 mm 360 (19 x 19 ball array - 1) 1.27 mm (50 mil) 2.22 mm 2.77 mm 0.75 mm (29.5 mil) 38 PC755/745 2138D-HIREL-06/03 PC755/745 Mechanical Dimensions of the PC755 PBGA Figure 26 provides the mechanical dimensions and bottom surface nomenclature of the PC755, 360 PBGA package. Figure 26. Mechanical Dimensions and Bottom Surface Nomenclature of the PC755 PBGA 2X 0.2 D A1 CORNER A C 0.15 C E NOTES: A. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. B. DIMENSIONS IN MILLIMETERS. C. TOP SIDE A1 CORNER INDEX IS A METALIZED FEATURE WITH VARIOUS SHAPES. BOTTOM SIDE A1 CORNER IS DESIGNATED WITH A BALL MISSING FROM THE ARRAY. 2X 0.2 B 1 2 3 4 5 6 7 8 9 10 111213141516 171819 W V U T R P N M L K J H G F E D C B A Millimeters DIM A M Min 2.22 0.50 1.00 0.60 Max 2.77 0.70 1.20 0.90 A1 A2 b D A2 A1 A 25.00 BSC 25.00 BSC 1.27 BSC E e e 360X b 0.3 C A B 0.15 C 39 2138D-HIREL-06/03 Mechanical Dimensions of the PC755 CBGA Package Figure 28 provides the mechanical dimensions and bottom surface nomenclature of the PC755, 360 CBGA package. Figure 27. Mechanical Dimensions and Bottom Surface Nomenclature of PC755 (CBGA) 2X 0.2 D A1 CORNER A D1 C 1 0.15 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. TOP SIDE A1 CORNER INDEX IS A METALIZED FEATURE WITH VARIOUS SHAPES. BOTTOM SIDE A1 CORNER IS DESIGNATED WITH A BALL MISSING FROM THE ARRAY. E1 E 2X 0.2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 171819 W V U T R P N M L K J H G F E D C B A Millimeters DIM A A1 A2 A3 b A3 A2 A1 A Min 2.65 0.79 1.10 -- 0.82 Max 3.20 0.99 1.30 0.60 0.93 D D1 E E1 e 25.00 BSC 6.75 25.00 BSC 7.87 1.27 BSC e 360X 0.3 C A B b 0.15 C 40 PC755/745 2138D-HIREL-06/03 PC755/745 Mechanical Dimensions of the PC755 HiTCE Package Figure 28 provides the mechanical dimensions and bottom surface nomenclature of the PC755, 360 HiTCE package. Figure 28. Mechanical Dimensions and Bottom Surface Nomenclature of PC755 (HiTCE) 2X 0.2 D A1 CORNER A D1 C 1 0.15 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. TOP SIDE A1 CORNER INDEX IS A METALIZED FEATURE WITH VARIOUS SHAPES. BOTTOM SIDE A1 CORNER IS DESIGNATED WITH A BALL MISSING FROM THE ARRAY. E E1 2X 0.2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 171819 W V U T R P N M L K J H G F E D C B A Millimeters DIM A A1 A2 A3 b A3 A2 A1 A Min 2.65 0.79 1.10 -- 0.82 Max 3.24 0.99 1.30 0.60 0.93 D D1 E E1 e 25.00 BSC 6.75 25.00 BSC 7.87 1.27 BSC e 360X 0.3 C A B b 0.15 C 41 2138D-HIREL-06/03 Mechanical Dimensions of the PC755 CI-CGA Package Figure 29 provides the mechanical dimensions and bottom surface nomenclature of PC755, 360 CI-CGA package Figure 29. Mechanical Dimensions and Bottom Surface Nomenclature of PC755 (CI-CGA) 2X 0.2 D A1 CORNER A A4 A A2 360 X 0.15 A D1 E E1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. TOP SIDE A1 CORNER INDEX IS A METALIZED FEATURE WITH VARIOUS SHAPES. BOTTOM SIDE A1 CORNER IS DESIGNATED WITH A BALL MISSING FROM THE ARRAY. 2X 0.2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 171819 W V U T R P N M L K J H G F E D C B A Millimeters DIM A A1 A2 A3 A4 A1 A3 A6 A5 Min Max 4.04 BSC 1.545 1.10 -- 0.82 1.695 1.30 0.60 0.9 A5 A6 b D 0.10 BSC 0.25 0.79 0.35 0.990 e 360X 25.00 BSC 6.75 25.00 BSC 7.87 0.3 C A B b 0.15 C D1 E E1 e 1.27 BSC Clock Relationship Choices The PC755's PLL is configured by the PLL_CFG[0-3] signals. For a given SYSCLK (bus) frequency, the PLL configuration signals set the internal CPU and VCO frequency of operation. The PLL configuration for the PC755 is shown in Figure 31 for example frequencies. 42 PC755/745 2138D-HIREL-06/03 PC755/745 Table 18. PC755 Microprocessor PLL Configuration Example Bus-to-Core Frequency in MHz (VCO Frequency in MHz) PLL_CFG [0-3] 0100 1000 1110 1010 0111 1011 1001 1101 0101 0010 0001 1100 0110 0011 1111 Notes: Bus-to-Core Multiplier 2x 3x 3.5x 4x 4.5x 5x 5.5x 6x 6.5x 7x 7.5x 8x 10x Core-to VCO Multiplier 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x Bus 33 MHz 200 (400) 216 (433) 233 (466) 250 (500) 266 (533) 333 (666) Bus 50 MHz 200 (400) 225 (450) 250 (500) 275 (550) 300 (600) 325 (650) 350 (700) 375 (750) 400 (800) Bus 66 MHz 200 (400) 233 (466) 266 (533) 300 (600) 333 (666) 366 5733 400 (800) Bus 75 MHz 225 (450) 263 (525) 300 (600) 338 (675) 375 (750) Bus 80 MHz 240 (480) 280 (560) 320 (640) 360 (720) 400 (800) Bus 100 MHz 200 (400) 300 (600) 350 (700) 400 (800) - PLL off/bypass PLL off PLL off, SYSCLK clocks core circuitry directly, 1x bus-to-core implied PLL off, no core clocking occurs 1. PLL_CFG[0:3] settings not listed are reserved. 2. The sample bus-to-core frequencies shown are for reference only. Some PLL configurations may select bus, core, or VCO frequencies which are not useful, not supported, or not tested for by the PC755; see Section Clock AC Specifications page 25 for valid SYSCLK, core, and VCO frequencies. 3. In PLL-bypass mode, the SYSCLK input signal clocks the internal processor directly, the PLL is disabled, and the bus mode is set for 1:1 mode operation. This mode is intended for factory use and emulator tool use only. Note: The AC timing specifications given in this document do not apply in PLL-bypass mode. 4. In PLL off mode, no clocking occurs inside the PC755 regardless of the SYSCLK input. 43 2138D-HIREL-06/03 The PC755 generates the clock for the external L2 synchronous data SRAMs by dividing the core clock frequency of the PC755. The divided-down clock is then phaseadjusted by an on-chip delay-lock-loop (DLL) circuit and should be routed from the PC755 to the external RAMs. A separate clock output, L2SYNC_OUT is sent out half the distance to the SRAMs and then returned as an input to the DLL on pin L2SYNC_IN so that the rising-edge of the clock as seen at the external RAMs can be aligned to the clocking of the internal latches in the L2 bus interface. The core-to-L2 frequency divisor for the L2 PLL is selected through the L2CLK bits of the L2CR register. Generally, the divisor must be chosen according to the frequency supported by the external RAMs, the frequency of the PC755 core, and the phase adjustment range that the L2 DLL supports. Figure 18 shows various example L2 clock frequencies that can be obtained for a given set of core frequencies. The minimum L2 frequency target is 80 MHz. Table 19. Sample Core-to-L2 Frequencies Core Frequency in MHz 250 266 275 300 325 333 350 366 375 400 1 250 266 275 300 325 333 350 366 375 400 1.5 166 177 183 200 217 222 233 244 250 266 2 125 133 138 150 163 167 175 183 188 200 2.5 100 106 110 120 130 133 140 146 150 160 3 83 89 92 100 108 111 117 122 125 133 Note: The core and L2 frequencies are for reference only. Some examples may represent core or L2 frequencies which are not useful, not supported, or not tested for by the PC755; see Section "L2 Clock AC Specifications" page 28 for valid L2CLK frequencies. The L2CR[L2SL] bit should be set for L2CLK frequencies less than 110 MHz. System Design Information PLL Power Supply Filtering The AVDD and L2AVDD power signals are provided on the PC755 to provide power to the clock generation phase-locked loop and L2 cache delay-locked loop respectively. To ensure stability of the internal clock, the power supplied to the AVDD input signal should be filtered of any noise in the 500 kHz to 10 MHz resonant frequency range of the PLL. A circuit similar to the one shown in Figure 31 using surface mount capacitors with minimum Effective Series Inductance (ESL) is recommended. Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a single large value capacitor. 44 PC755/745 2138D-HIREL-06/03 PC755/745 The circuit should be placed as close as possible to the AVDD pin to minimize noise coupled from nearby circuits. An identical but separate circuit should be placed as close as possible to the L2AVDD pin. It is often possible to route directly from the capacitors to the AVDD pin, which is on the periphery of the 360 BGA footprint, without the inductance of vias. The L2AVDD pin may be more difficult to route but is proportionately less critical. Figure 30. PLL Power Supply Filter Circuit VDD 10 2.2 F 2.2 F Low ESL Surface Mount Capacitors GND AVDD (or L2AVDD) Power Supply Voltage Sequencing The notes in Figure 32 contain cautions about the sequencing of the external bus voltages and core voltage of the PC755 (when they are different). These cautions are necessary for the long term reliability of the part. If they are violated, the ESD (Electrostatic Discharge) protection diodes will be forward biased and excessive current can flow through these diodes. If the system power supply design does not control the voltage sequencing, the circuit of Figure 32 can be added to meet these requirements. The MUR420 Schottky diodes of Figure 32 control the maximum potential difference between the external bus and core power supplies on power-up and the 1N5820 diodes regulate the maximum potential difference on power-down. Figure 31. Example Voltage Sequencing Circuit 3.3V MURS320 MURS320 2.0V 1N5820 1N5820 Decoupling Recommendations Due to the PC755's dynamic power management feature, large address and data buses, and high operating frequencies, the PC755 can generate transient power surges and high frequency noise in its power supply, especially while driving large capacitive loads. This noise must be prevented from reaching other components in the PC755 system, and the PC755 itself requires a clean, tightly regulated source of power. Therefore, it is recommended that the system designer place at least one decoupling capacitor at each VDD, OVDD, and L2OV DD pin of the PC755. It is also recommended that these decoupling capacitors receive their power from separate VDD, (L2)OVDD and GND power planes in the PCB, utilizing short traces to minimize inductance. These capacitors should have a value of 0.01 F or 0.1 F. Only ceramic SMT (surface mount technology) capacitors should be used to minimize lead inductance, preferably 0508 or 0603 orientations where connections are made along the length of the part. 45 2138D-HIREL-06/03 In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB, feeding the VDD, L2OVDD, and OV vplanes, to enable quick recharging of the smaller chip capacitors. These bulk capacitors should have a low ESR (equivalent series resistance) rating to ensure the quick response time necessary. They should also be connected to the power and ground planes through two vias to minimize inductance. Suggested bulk capacitors - 100-330 F (AVX TPS tantalum or Sanyo OSCON). Connection Recommendations To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal level through a resistor. Unused active low inputs should be tied to OVDD. Unused active high inputs should be connected to GND. All NC (no-connect) signals must remain unconnected. Power and ground connections must be made to all external VDD, OVDD, L2OVDD, and GND pins of the PC755. Output Buffer DC Impedance The PC755 60x and L2 I/O drivers are characterized over process, voltage, and temperature. To measure Z0, an external resistor is connected from the chip pad to (L2)OVDD or GND. Then, the value of each resistor is varied until the pad voltage is (L2)OVDD/2 (See Figure 33). The output impedance is the average of two components, the resistances of the pull-up and pull-down devices. When Data is held low, SW2 is closed (SW1 is open), and RN is trimmed until the voltage at the pad equals (L2)OVDD/2. RN then becomes the resistance of the pull-down devices. When Data is held high, SW1 is closed (SW2 is open), and R P is trimmed until the voltage at the pad equals (L2)OVDD/2. RP then becomes the resistance of the pull-up devices. NO TAG describes the driver impedance measurement circuit described above. Figure 32. Driver Impedance Measurement Circuit (L2)OVDD (L2)OVDD RN SW2 Data Pad SW1 RP OGND 46 PC755/745 2138D-HIREL-06/03 PC755/745 Alternately, the following is another method to determine the output impedance of the PC755. A voltage source, Vforce, is connected to the output of the PC755 as in Figure 33. Data is held low, the voltage source is set to a value that is equal to (L2)OVDD/2 and the current sourced by Vforce is measured. The voltage drop across the pull-down device, which is equal to (L2)OVDD/2, is divided by the measured current to determine the output impedance of the pull-down device, RN. Similarly, the impedance of the pull-up device is determined by dividing the voltage drop of the pull-up, (L2)OVDD/2, by the current sank by the pull-up when the data is high and Vforce is equal to (L2)OVDD/2. This method can be employed with either empirical data from a test set up or with data from simulation models, such as IBIS. RP and RN are designed to be close to each other in value. Then Z0 = (RP + RN)/2. Figure 33 describes the alternate driver impedance measurement circuit. Figure 33. Alternate Driver Impedance Measurement Circuit (L2)OVDD BGA Pin Data Vforce OGND Table 20 summarizes the signal impedance results. The driver impedance values were characterized at 0C, 65C, and 105C. The impedance increases with junction temperature and is relatively unaffected by bus voltage. Table 20. Impedance Characteristics VDD = 2.0V, OVDD = 3.3V, Tc = 0 - 105C Impedance RN RP Processor bus 25-36 26-39 L2 bus 25-36 26-39 Symbol Z0 Z0 Unit W W Pull-up Resistor Requirements The PC755 requires pull-up resistors (1 k - 5 k) on several control pins of the bus interface to maintain the control signals in the negated state after they have been actively negated and released by the processor or other bus masters. These pins are TS, ABB, AACK, ARTRY, DBB, DBWO, TA, TEA, and DBDIS. DRTRY should also be connected to a pull-up resistor (1 k - 5 k) if it will be used by the system; otherwise, this signal should be connected to HRESET to select NO-DRTRY mode. Three test pins also require pull-up resistors (100 - 1 k). These pins are L1_TSTCLK, L2_TSTCLK, and LSSD_MODE. These signals are for factory use only and must be pulled up to OVDD for normal machine operation. 47 2138D-HIREL-06/03 In addition, CKSTP_OUT is an open-drain style output that requires a pull-up resistor (1 k - 5 k) if it is used by the system. During inactive periods on the bus, the address and transfer attributes may not be driven by any master and may, therefore, float in the high-impedance state for relatively long periods of time. Since the processor must continually monitor these signals for snooping, this float condition may cause additional power draw by the input receivers on the processor or by other receivers in the system. These signals can be pulled up through weak (10 k) pull-up resistors by the system or may be otherwise driven by the system during inactive periods of the bus to avoid this additional power draw, but address bus pull-up resistors are not neccessary for proper device operation. The snooped address and transfer attribute inputs are: A[0:31], AP[0:3], TT[0:4], TBST, and GBL. The data bus input receivers are normally turned off when no read operation is in progress and, therefore, do not require pull-up resistors on the bus. Other data bus receivers in the system, however, may require pull-ups, or that those signals be otherwise driven by the system during inactive periods by the system. The data bus signals are: DH[0:31], DL[0:31], and DP[0:7]. If 32-bit data bus mode is selected, the input receivers of the unused data and parity bits will be disabled, and their outputs will drive logic zeros when they would otherwise normally be driven. For this mode, these pins do not require pull-up resistors, and should be left unconnected by the system to minimize possible output switching. If address or data parity is not used by the system, and the respective parity checking is disabled through HID0, the input receivers for those pins are disabled, and those pins do not require pull-up resistors and should be left unconnected by the system. If all parity generation is disabled through HID0, then all parity checking should also be disabled through HID0, and all parity pins may be left unconnected by the system. Definitions Datasheet Status Objective specification Target specification Preliminary specification site Preliminary specification site Product specification Limiting Values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application Information Where application information is given, it is advisory and does not form part of the specification. This datasheet contains target and goal specification for discussion with customer and application validation. This datasheet contains target or goal specification for product development. This datasheet contains preliminary data. Additional data may be published later; could include simulation result. This datasheet contains also characterization results. This datasheet contains final product specification. Validity Before design phase. Valid during the design phase. Valid before characterization phase. Valid before the industrialization phase. Valid for production purpose. 48 PC755/745 2138D-HIREL-06/03 PC755/745 Life Support Applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Atmel customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnity Atmel for any damages resulting from such improper use or sale. Differences with Commercial Part Commercial part Temperature range Tj = 0 to 105C Military part Tj = -55C to 125C Ordering Information PC755C Type M ZF U 300 L x Revision Level(1) E: Rev. 2.8 Bus divider (to be confirmed) L: Any valid PLL configuration Max internal processor speed 300: 300 MHz 350: 350 MHz 366: 366 MHz 400: 400 MHz Temperature Range: Tj M: -55 C, +125 C V: -40 C, +110 C Package: ZF: FC-PBGA G: CBGA GS: CI-CGA GH: HiTCE Screening Level(1) U: Upscreening Test Note: For availability of different versions, contact your Atmel sales office. 49 2138D-HIREL-06/03 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 literature@atmel.com Web Site http://www.atmel.com Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems. (c) Atmel Corporation 2003. All rights reserved. Atmel (R) and combinations thereof, are the registered trademarks of Atmel Corporation or its subsidiaries. The PowerPC names and the PowerPC logotype are trademarks of International Business Machines Corporation, used under license therform. Motorola is the registered trademark of Motorola, Inc. AltiVec TM is a trademark of Motorola, Inc. Other terms and product names may be the trademarks of others. Printed on recycled paper. 2138D-HIREL-06/03 0M |
Price & Availability of PC755CVGU400LE
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |